Kitchenaid stand mixer head wobbles and jumps - what's wrong? - Kitchen Seer (2022)

If the head of your Kitchenaid stand mixer is bouncing and bouncing, it's not being able to use its full potential. The other frustrating part is figuring out what is causing the problem. Let's take a look below.

If your Kitchenaid mixer head wobbles and jumps, it could be because:

  • The fly meter is too high or too low.
  • Perder Halsnadel.
  • The bowl is not properly latched.
  • Worn beater bushings.
  • Very warped bowl.

Any of these causes can be resolved with some troubleshooting. This article looks at each possible cause and how to fix it. Plus, we've answered other frequently asked questions about the Kitchenaid stand mixer, so read on!

Kitchenaid stand mixer head wobbles and jumps - what's wrong? - Kitchen Seer (1)

Why is my Kitchenaid mixer head shaking?

If you like to cook or bake, you know how important it is to have aKitchen helperMixer. This desktop mixer is a powerhouse that can knead bread dough, mix cake batter, and more.

However, it can be very frustrating when it doesn't work properly. A common problem is when the blender head starts to wobble and wobble while blending. This can make it difficult to use the blender to its full potential.

You'll find that the ingredients don't mix as well as they should, and you may even end up with a countertop mess. So what is causing this problem? Let's take a look at some of the possible causes.

Kitchenaid stand mixer head wobbles and jumps - what's wrong? - Kitchen Seer (2)

Fly meter is too high or too low

A possible reason why the Kitchenaid mixer head is bouncing is that thestickBlade is too high or too low. If the blade is set too high, it can hit the sides of the bowl and cause the blender to vibrate.

On the other hand, if the blade is set too low, you cannot mix the ingredients well. This can also cause the mixer to vibrate.

To fix this problem, you need to adjust the fly meter. You can do this by loosening the screw on the bottom of the blender and moving the blade up or down until it is the correct height.

perder Halsnadel

Another possible reason for an unstable blender head is a loose neck pin. Over time, the neck pin can come loose and the fur can wobble.

If you notice the neck pin sticking out of the blender, that's probably the problem. To fix this you will need a flat head screwdriver.

Then set aside the mixture to access the screw that secures the neck pin. Tighten the screw until secure. Be careful not to over-tighten as this could damage the screw.

The bowl is not properly closed

If the bowl is not latched properly, it can also cause the mixer head to wobble. You need to make sure the bowl is locked in place before mixing.

To do this, push the tray up until it clicks into place. You'll know it's stuck when you can't move the bowl up or down.

Worn racket shaft bushings

Another possible cause of an unstable agitator head is worn impact shaft bushings. Over time, the bushings can wear out and cause the head to wobble.

To fix this problem, you need to change the bushings. You can remove the screw that holds the racquet shaft in place, then take out the old bushings.

Then insert the new bushings and screw the beater shaft again.

heavily warped bowl

If your bowl is warped, it can also cause the mixer head to wobble. A warped bowl can cause the head to wobble during processing, making it difficult to use the blender properly.

You can replace the bowl by going to the Kitchenaid website and ordering a new one.

Do Kitchenaid stand mixers have a lifetime warranty?

Unfortunately, Kitchenaid does not offer a lifetime warranty on its blenders. However, they do offer a full one year warranty on all of their products.

The warranty begins on the date of purchase and covers defects in material or workmanship. Therefore, if your blender breaks down within the first year of purchase, you can replace or repair it for free.

You may contact Kitchenaid's Customer Service Department to initiate the warranty process. When contacting customer service, be sure to have your purchase receipt and blender serial number ready.

You should also describe the problem you are having with your blender.

Kitchenaid stand mixer head wobbles and jumps - what's wrong? - Kitchen Seer (3)

Do Kitchenaid stand mixers need oiling?

Yes, Kitchenaid stand mixers need to be oiled regularly. How often do you need to do thisoilYour blender depends on how often you use it.

If you use your blender frequently, you'll need to lubricate it every few months. However, if you use it occasionally, you can lubricate it once a year.

You can purchase Kitchenaid Blender Oil from the Kitchenaid website or from any other retailer that sells Kitchenaid products.

When applying the oil, make sure you only use a small amount. Excess oil can cause the blender to overheat and damage the motor.

Also, be sure to wipe off excess oil after application.

How to Clean a Kitchenaid Stand Mixer

Cleaning a Kitchenaid blender is a relatively simple process. The first thing you need to do is turn off the blender.

Then remove the blender bowl and accessories. Next, you need to clean the outside of the blender with a damp cloth.

Be careful not to get water on the blender's electrical components. Once the outside is clean, you can clean the bowl and accessories.

The bowl should be hand washed in warm, soapy water. Stainless steel and coated accessories can be washed in theDishwasher.

However, plastic accessories should only be cleaned by hand.

When everything is clean, you can reassemble the blender and plug it back in.

Kitchenaid stand mixer head wobbles and jumps - what's wrong? - Kitchen Seer (4)

How long do Kitchenaid stand mixers last?

Depending on how often you use your blender, a Kitchenaid blender can last five to five years.fifteenYears.

Obviously, the more you use the blender, the faster it wears out.

However, if you take good care of your blender and oil it regularly, it should last for many years. In addition, tightening loose parts and replacing worn parts will also help extend the life of your blender.

What is the Kitchenaid Coin Test?

The Kitchenaid Cent Test is a great way to position your bowl on the stand mixer so it doesn't wobble.

To do the coin test, place a coin in the center of the bowl. Then place the bowl in the blender and turn it to the lowest setting.

If the coin stays in place, your club is too high. If the currency is moving quickly, your club is low.

You will need to adjust the height of the beater until the coin slowly rotates around the bowl. This is a handy trick to get the perfect mixing consistency every time.

Can a Kitchenaid stand mixer be stored on its side?

Ideally, a Kitchenaid blender should be keptna verticalon your counter. However, they can take up a lot of space, so storing them at waist-to-chest height on a shelf is also acceptable.

If you store the blender too high or too low, you could injure yourself or fall and damage the blender.

It can be damaged if you have to store the blender on its side. Parts may come off or the blender may not work properly when you use it again.

Why does my Kitchenaid stand mixer make so much noise?

Kitchenaid stand mixer head wobbles and jumps - what's wrong? - Kitchen Seer (5)

If you notice that your Kitchenaid Mixer isvolume upthan normal, something may be wrong with the engine.

First check that all parts are tight. In that case, you will have to take it to a professional to have the engine checked.

It is also possible that your blender needs lubrication. Be sure to oil your blender regularly to keep it running smoothly.

If you've followed all these steps and your blender is still making noise, it might be time for a new one.

final thoughts

Kitchenaid stand mixer head wobbles and jumps - what's wrong? - Kitchen Seer (6)

By following these tips, you can ensure that your Kitchenaid stand mixer lasts for years to come. Make sure you lubricate it regularly and clean it after each use.

If you notice any unusual noise or vibration, take the mixer to a professional to have it checked.

Did it come to an end? Here are other articles you might like:

Should my Kitchenaid stand mixer be making this much noise?

Can I use a food processor as a blender?

How much does a Cuisinart blender weigh?

Top Articles

You might also like

Latest Posts

Article information

Author: Twana Towne Ret

Last Updated: 10/01/2022

Views: 5912

Rating: 4.3 / 5 (44 voted)

Reviews: 91% of readers found this page helpful

Author information

Name: Twana Towne Ret

Birthday: 1994-03-19

Address: Apt. 990 97439 Corwin Motorway, Port Eliseoburgh, NM 99144-2618

Phone: +5958753152963

Job: National Specialist

Hobby: Kayaking, Photography, Skydiving, Embroidery, Leather crafting, Orienteering, Cooking

Introduction: My name is Twana Towne Ret, I am a famous, talented, joyous, perfect, powerful, inquisitive, lovely person who loves writing and wants to share my knowledge and understanding with you.